You may want a copied trade to start with the Transmitter’s Stop Loss and Take Profit, then manage its exit levels yourself on the Receiver. Local Trade Copier EA MT4/5© provides Allow TP/SL Manual Change for this workflow.
Enable the setting on the Receiver. LTC continues synchronizing the original trade’s TP/SL changes until you manually modify the copied trade’s TP or SL. After that manual modification, LTC stops updating those TP/SL levels from the original trade.
That change applies to the copied trade you modified. Decide how you want to manage its levels before making the adjustment.
Choose the exit-level workflow you need
Your intended workflow
Relevant Receiver settings
Follow the Transmitter’s SL and TP
Enable Copy Stop Loss and Copy Take Profit and use the normal synchronization configuration.
Start with copied levels, then adjust a particular copy manually
Enable Copy Stop Loss, Copy Take Profit and Allow TP/SL Manual Change.
Adjust copied distances using a repeatable rule
Review the SL/TP multipliers, point adjustments and Keep Original TP/SL Distances in the Inputs Guide.
With manual changes enabled, changing either the Receiver SL or TP ends source-driven TP/SL updates for that modified copy. Check both levels after the change, even if you edited only one of them. The Settings & Inputs Guide describes these controls under Copying / Multiplying Options.
Prepare a demo position
Use the downloadable LTC demo on two MetaTrader demo accounts in separate terminals on the same Windows computer or VPS. Follow the Installation Guide if the terminals are not connected yet.
Use a mapped symbol that is open for trading. For this demonstration, choose Fixed Lot sizing with a small valid demo volume. Enable Copy Stop Loss, Copy Take Profit and Allow TP/SL Manual Change on the Receiver. Keep SL/TP multipliers at 1, point adjustments at 0, and other independent exit controls from intervening during the test. Choose levels far enough from the market to remain open during the checks and satisfy both brokers’ stop-distance requirements.
Open a fresh market position on the Transmitter with both an SL and a TP. Check the corresponding Receiver position in its Trade tab. Record the entry, SL and TP on each account.
The Receiver may fill at a different entry price. Its initial levels also depend on Keep Original TP/SL Distances. Use the actual displayed values as your baseline.
Modify the Transmitter’s SL to another valid level while leaving the position open. Check that LTC updates the copied position’s SL according to the Receiver configuration.
This establishes that synchronization is working before you make a manual Receiver change.
Open the copied position’s modification window on the Receiver. Change its SL to a different valid level, retain a valid TP, and apply the modification.
Record both Receiver levels after the broker accepts the change. You have now made the manual modification that ends source-driven TP/SL updates for this copy.
Change the Transmitter’s SL and TP again, using valid levels that keep the demo position open. Check that the modified Receiver copy retains the SL and TP recorded in Step 3.
Close the demo positions when the checks are complete. If a modification is rejected or the result differs, review the input values and the Experts and Journal tabs. The Troubleshooting Guide helps you check the setup.
After a manual SL change on the Receiver, the copied position retained its SL and TP when the Transmitter’s levels were modified again. Allow TP/SL Manual Change was enabled on the Receiver.
Allow TP/SL Manual Change controls synchronization of the copied position’s exit levels. If Synchronize Trade Closure is enabled, a later Transmitter closure can still close the corresponding Receiver trade.
Other Receiver exit controls can also act on the position. Test your intended closure configuration alongside manual level changes before using the workflow with an active account. Our guide to controlling, filtering and managing trades across multiple accounts explains the broader choices.
The demo above uses a fixed lot size to isolate level management. With risk-based sizing, the initial calculation depends on the Stop Loss distance. Moving the SL changes the potential loss for the open volume. Review the resulting exposure after a manual adjustment.
Use the trade copier lot-sizing guide when choosing how each Receiver should size new entries.
If you have questions about installation, configuration, copying between MT4 and MT5, or managing multiple receiver accounts, check our guides or contact us directly.